![]() If ((irq_delta + steal) & sched_feat(NONTASK_CAPACITY)) It sits in theĬlock hierarchy between rq->clock_task and rq->clock_pelt. Internally, a new clock is created: rq->clock_task_mult. This clock multiplierĪrtificially speeds up PELT ramp up/down similarly to use a faster Multiplier to x2 or x4 (x1 being the default). The new sysctl sched_pelt_multiplier allows a user to set a clock ![]() ![]() Qais Yousef sched/pelt: Introduce PELT multiplierĭate: Mon, 07:54:50 +0200 Lambda: "return id($devicename).Sched/pelt: Introduce PELT multiplier - Dietmar Eggemann archive mirror help / color / mirror / Atom feed From: Dietmar Eggemann Lambda: "return id($devicename).valve_run_duration(2) " Lambda: "return id($devicename).valve_run_duration(1) " Lambda: "return id($devicename).valve_run_duration(0) " Std::string progress_percent_as_string = std::to_string(progress_percent) Int progress_percent = round(((id($devicename).valve_run_duration_adjusted(id($devicename).active_valve().value_or(0)) - id($devicename).time_remaining().value_or(0)) * 100 / id($devicename).valve_run_duration_adjusted(id($devicename).active_valve().value_or(0)))) (minutes ? String(minutes) + "m " : "") + Int seconds = round(id($devicename).time_remaining().value_or(0)) Update_interval: $sensor_update_frequency # WiFi connection, replace these with values for your WiFi. # Set multiplier to 60, convert seconds to minutes #Define Project Deatils and ESP Board Type Upper_devicename: Four Valve Irrigation Ctrl - $unit_id # DO NOT CHANGE ANYTHING BELOW THIS LINE #Įsphome_name: irrigation-valve-ctrl-unit-$devicename_unit_idĮsphome_comment: Four Valve Irrigation Control - $unit_idĮsphome_project_name: Robert.Four Valve Irrigation Control - $unit_idĮsphome_project_version: Four Valve Irrigation Ctrl - Unit $unit_id, $software_versionĭevicename: irrigation_valve_controller_unit_$devicename_unit_id # - Change update_interval to 120s - test to see if 1s update resolves problem of slow Google response text_sensor updates automatically when data is passed to it through text_. # - Change update_interval for valve_status_$devicename_unit_id to 'never'. # - Remove " Duration (Seconds)" from number template name: # - Add UOM for Number sensors - Set to "Sec" # - Convert Percentage Remaining sensor to text_sensor # - Convert Time Remaining sensor to text_sensor # - Add icons to Time Remaining, Progress and Status sensors # - Rename Start/Resume to Start/Stop/Resume # - Replace occurances of $ with $software_version # - Add sensor_update_frequency as a substitution for update_interval # - Add "Progress %" attribute for all zones # - Add "Time Remaining" attribute for all zones # - Remove the word "Unit" from substitutions # - Add on_boot function to set value of valve_status # - Rename lawn_sprinkler_ctrlr_status to valve_status # - Revised numbering of zone_x_valve_id: substitution - 1 to 4 instead of 0 - 3 # - Renamed zone_x_id: substitution to zone_x_valve_id: # - Revised numbering of zone_x_name: substitution - 1 to 4 instead of 0 - 3 # - Added code for Sprinkler Status, Time Remaining and Percentage Complete # - Corrected valve number sequenceing in number: template: section. Lambda: "return id(irrigation_valve_controller_unit_a).valve_run_duration(0) "Ĭhange valve_0, Rear Lawn, unit_of_measure and devicename (In my case this is irrigation_valve_controller_unit_a) to match corresponding names used in your code.įor refernce, my code is # Based on ESPHome Sprinkler Controller. Mode: box # Defines how the number should be displayed in the UI Lambda: "return id(controller_irrigazione).multiplier() "įor each sprinkler, you’ll want to add something like the following to your number: section number: Currently I can set the single timer for all 3 zones.Īuto_advance_switch: "Irrigatori Auto Advance" However, I would like to be able to set the timer for each individual valve (zone). I am testing the new “Sprinkler Controller” component.
0 Comments
Leave a Reply. |